

Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Toyota Car Yaris
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
2 Weekly Tire Inflation Pressure Check
Instructions for checking tire inflation pressure
Tires are cold (Vehicle has been parked for at least 3 hours or has not been driven for more than 1.5 km or 1 mile)
Enter the tire inflation pressure reading
Tire pressure gauge used for measurement
Tire inflation pressure not reduced after driving
Passengers and luggage weight balanced
WARNING: Proper inflation is critical to save tire performance
Tires properly inflated
No excessive wear on tires
Air Conditioning Filter Maintenance
Warning: Ensure the power switch is off before starting the procedure.
Power switch turned off?
Glove box opened and damper slid off?
Glove box pulled out and lower claws disconnected?
Filter cover unlocked and removed?
Select the type of filter
Filter or filter case removed?
New air conditioning filter replaced with 'UP' marks pointing up?
Check and replace the air conditioning filter according to the maintenance schedule.
Air Intake Vent And Filter Cleaning
Warning: This procedure requires careful handling of the air intake vent and filter. Do not use water or other liquids to clean the air intake vent. If water is applied to the hybrid battery (traction battery) or other components, a malfunction or fire may occur.
Is the hybrid battery air intake vent dusty or clogged?
If the air intake vent is dusty or clogged, proceed with the following steps.
Remove the dust from the air intake vent with a vacuum cleaner.
Warning: Do not attempt to blow out dust and clogs using an airgun, etc. This may push it into the air intake vent.
If dust and clogs cannot be completely removed with the air intake vent cover installed, remove the cover and clean the filter.
To remove the air intake vent cover, turn the power switch off and use a flathead screwdriver.
Remove the air intake vent filter.
Remove the dust and clogs from the filter using a vacuum cleaner.
Battery Maintenance
Warning: Battery maintenance requires trained personnel with PPE!
12-volt battery cover removed
Screws removed
Clips removed from the claws
Tabs slid out of the notches
Before recharging: The 12-volt battery produces hydrogen gas which is flammable and explosive.
Ground cable disconnected before recharging
Power switch on the charger is off when connecting and disconnecting the charger cables to the 12-volt battery
After recharging/reconnecting the 12-volt battery (vehicles with a smart entry & start system)
Coolant Check
Warning: Do not remove the engine/power control unit coolant reservoir caps when the hybrid system is hot. The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing serious injuries, such as burns.
Engine coolant reservoir level between the “F” and “L” lines when the engine is cold
Power control unit coolant reservoir level between the “F” and “L” lines when the hybrid system is cold
Coolant selection
If the coolant level drops within a short time of replenishing, visually check the radiator, hoses, engine/power control unit coolant reservoir caps, drain cock and water pump.
No visible leaks in the cooling system
Notice: When adding coolant, coolant is neither plain water nor straight antifreeze. The correct mixture of water and antifreeze must be used to provide proper lubrication, corrosion protection and cooling. Be sure to read the antifreeze or coolant label.
No coolant spillage
Sign off on the coolant check
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













