Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.

Documents & Manuals

Find all the essential guides in one place.

Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more

Work Order Templates

Pre-built workflows to keep your asset running smoothly.

Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more

Procedures

Integrate maintenance plans directly into your work orders.

Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more

Parts

Access the parts list for your equipment in MaintainX.

Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Nilfisk Scrubber BA 611D

Create an account to install this asset package.

Maintenance Plans for Nilfisk Scrubber Model BA 611D

Integrate maintenance plans directly into your work orders in MaintainX.

1 Weekly Vacuum System Motor Filter Cleaning

If the tank (21) contains recovery water

Select the machine model

Drive the machine to the appointed recovery water disposal area

Turn off the machine

Empty the recovery water tank (21) with the hose (16)

Drive the machine on a level floor

Turn off the machine

For CA 451, CA 531, CA 551

Open the recovery water tank cover (22)

Run this procedure

1 Yearly Drive System Motor Carbon Brush Maintenance

Machine driven to the appointed disposal area and recovery water tank emptied

Machine placed on a hoisting system or level floor

Ignition key turned to “0”

Battery connector disconnected

Drive system motor cleaned in the area of the covers

Covers unscrewed and carbon brushes removed

Check if the carbon brushes are worn

Carbon brushes replaced if necessary

Components assembled in the reverse order of disassembly

Run this procedure

1 Weekly Squeegee Blade Check and Replacement

Cleaning the squeegee

Cleaned the steel squeegee or the aluminium squeegee

Checking the edges of the blades

Checked that the edges of the front blade and the edges of the rear blade lay down on the same level

Adjusting the height of the blades

Adjusted the height of the blades

Checking the blades for integrity, cuts and tears

Checked the front blade and rear blade for integrity, cuts and tears

Replacing the blades if necessary

Run this procedure

6 Monthly Screw and Nut Tightening Check

Drive the machine to the appointed disposal area

Empty the recovery water tank (21) with the hose (16)

Place the machine on a hoisting system (if available). Otherwise, drive the machine on a level floor

Turn off the machine

(For BA 451D, BA 531D, BA 551D, BA 551CD, BA 611D) Turn the ignition key (80) to “0”

(For BA 451, BA 531, BA 551) Turn off the switches (71) and (73)

(For CA 451, CA 531, CA 551) Disconnect the power supply cable (59) from the electrical mains

Open the recovery water tank cover (22)

Remove the retaining plate (61) of the tank (40)

Run this procedure

1 Daily Recovery Water Tank and Vacuum Grid Cleaning

Drive the machine to the appointed recovery water disposal area

Turn off the machine

Lift the cover (A) to washing position (L)

Wash with clean water the cover (A), the tank (B) and the vacuum grid with automatic shut-off float (D)

Drain the water in the tank through the hose (16). If necessary, release the fasteners (E) and open the grid (D), recover the float (F), clean all the components and then reinstall them

Check the tank cover gasket (G) for integrity

NOTE: The hole (K), allowing to compensate the air in the cover interspaces, contributes to create vacuum in the tank. If necessary replace the gasket (G) by removing it from its housing (H). When assembling the new gasket, install the joint (I) in the rear central area, as shown in the figure

Check that the bearing surface (J) of the gasket (G) is integral and adequate for the gasket itself

Check the compensation hole (K) for clogging, and clean it if necessary

Run this procedure