Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Mitsubishi Split-Type, Heat Pump Air Conditioner PUMY-SP125YKM.TH
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
Low Pressure Sensor and High Pressure Sensor Disassembling
Remove the service panel
Upload a photo of the removed service panel
Remove the top panel
Upload a photo of the removed top panel
Remove the side panel (R)
Disconnect the connector 63LS (blue) and the 63HS(white) on the multi controller circuit board in the electrical parts box
Loosen the clamps, which are fixing the low pressure sensor and high pressure sensor lead wire to the top of the electrical parts box
Upload a photo of the loosened clamps
Recover refrigerant
LEV Coil Disassembling
[LEV-A]
(1) Remove the service panel. (See Photo 1)
(2) Disconnect the connector CNL VA (WH) on the multi controller circuit board in the electrical parts box.
(3) Remove the LEV coil by sliding the coil upward. (See Photo 13)
[LEV-B]
(1) Remove the service panel. (See Photo 1)
(2) Disconnect the connector CNL VB (RD) on the multi controller circuit board in the electrical parts box.
(3) Remove the LEV coil by sliding the coil upward. (See Photo 13);
Accumulator Disassembling
Remove the service panel
Upload a photo of the removed service panel
Remove the top panel
Upload a photo of the removed top panel
Remove the electrical parts box
Remove the valve bed
Remove the cover panel (front)
Remove the cover panel (rear)
Remove the side panel (R)
4-Way Valve Disassembling
Upload Photo 1 of the service panel and top panel removed
Upload procedure 3 for removing the electrical parts box
Upload Photo 4 of the valve bed removed
Upload Photo of the right side panel removed
Upload Photo 15 of the 4-way valve coil removed
Refrigerant recovered without spreading in the air?
Welded part of 4-way valve removed?
Note: The welded part can be removed easily by removing the right side panel.
Note: When installing the 4-way valve, cover it with a wet cloth to prevent it from heating (120°C or more), then braze the pipes so that the inside of pipes are not oxidized.
Compressor Disassembling
Upload Photo 1 of the service panel and top panel removal
Service panel removed
Top panel removed
Refer to procedure 3 for removing the electrical parts box
Electrical parts box removed
Number of valve bed fixing screws removed
Number of stop valve fixing screws removed
Valve bed removed
Number of cover panel (front) fixing screws removed
Access the parts list for your equipment in MaintainX.
Joint
CMY-Y62-G-E
Header
CMY-Y64/68-G-E
Joint
CMY-Y62-G-E
Header
CMY-Y64/68-G-E
Joint
CMY-Y62-G-E
Header
CMY-Y64/68-G-E
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













