Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Mitsubishi Split-Type, Heat Pump Air Conditioner PUMY-SP125VKMR1.TH
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
TH2 and TH4 Thermistors Disassembling
(1) Remove the service panel. (See Photo 1)
(2) Remove the top panel. (See Photo 1)
(3) Disconnect the following connectors on the controller circuit board in the electrical parts box.
•TH2: Black
•TH4:White
[Removing the thermistor <HIC> (TH2)]
(4) Loosen the fastener fixing the connector to the electrical parts box. (See Photo 10)
(5) Pull out the thermistor <HIC> (TH2) from the sensor holder. (See Photo 13)
[Removing the thermistor <Compressor> (TH4)]
LEV Disassembling
Remove the service panel
Upload a photo of the removed service panel
Remove the top panel
Upload a photo of the removed top panel
Remove the electrical parts box
Remove the LEV coil
Recover refrigerant without spreading it in the air
Remove the welded part of LEV
Note: The welded part can be removed easily by removing the right side panel.
LEV Coil Disassembling
[LEV-A]
(1) Remove the service panel. (See Photo 1)
(2) Disconnect the connector CNL VA (WH) on the multi controller circuit board in the electrical parts box.
(3) Remove the LEV coil by sliding the coil upward. (See Photo 13)
[LEV-B]
(1) Remove the service panel. (See Photo 1)
(2) Disconnect the connector CNL VB (RD) on the multi controller circuit board in the electrical parts box.
(3) Remove the LEV coil by sliding the coil upward. (See Photo 13);
Fan Motor Disassembling
Remove the service panel
Upload a photo of the removed service panel
Remove the top panel
Upload a photo of the removed top panel
Remove 4 fan grille fixing screws (5 × 12) to detach the fan grille
Upload a photo of the detached fan grille
Remove a nut (for right handed screw of M6) to detach the propeller
Upload a photo of the detached propeller
Disconnect the connector CNF1 on the multi controller circuit board in the electrical parts box
Outdoor Unit Refrigirant Charging
Cautions for service
Refrigerant recovered from the unit completely
Refrigerant not released in the air
Cycle charged with specified amount of refrigerant after service
Filter drier installed for service
Filter drier used for new refrigerant
Additional refrigerant charge
Cylinder for R410A is a syphon type
Charging performed with the cylinder of syphon stood vertically
Access the parts list for your equipment in MaintainX.
Joint
CMY-Y62-G-E
Header
CMY-Y64/68-G-E
Joint
CMY-Y62-G-E
Header
CMY-Y64/68-G-E
Joint
CMY-Y62-G-E
Header
CMY-Y64/68-G-E
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













