Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Mitsubishi Split-Type, Heat Pump Air Conditioner PUMY-SP125VKM.TH-BS
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
4-Way Valve Coil Disassembling
Remove the service panel
Upload a photo of the removed service panel
Remove 4-way valve coil fixing screw (M5 × 7)
Remove the 4-way valve coil by sliding the coil toward you
Disconnect the connector 21S4 (green) on the outdoor multi controller circuit board in the electrical parts box
Sign off on the disassembling process
4-Way Valve Disassembling
Upload Photo 1 of the service panel and top panel removal
Upload Photo 4 of the valve bed removal
Upload Photo 15 of the 4-way valve coil removal
Note 1: Recover refrigerant without spreading it in the air.
Note 2: The welded part can be removed easily by removing the right side panel.
Note 3: When installing the 4-way valve, cover it with a wet cloth to prevent it from heating (120°C or more), then braze the pipes so that the inside of pipes are not oxidized.
Service panel removed?
Top panel removed?
Electrical parts box removed?
Electrical Parts Box Replacement
Upload Photo 1 of the service panel and top panel removal
Upload Photo 5 or 7 of the disconnected connecting wire from terminal block
Disconnected the connector CNF1, 4-way valve coil, LEV-A and LEV-B on the multi controller circuit board?
Disconnected the pipe-side connections of the following parts: Thermistor <HIC> (TH2), Thermistor <Compressor> (TH4), Thermistor <Liquid> (TH3), Thermistor <Suction> (TH6), Thermistor <Ambient> (TH7)?
Removed the comp felt (top)?
Upload Photo 11 of the removed nut from the terminal cover and disconnected compressor lead wire
Removed 2 electrical parts box fixing screws (4 × 10), and detached the electrical parts box by pulling upward?
Sign off on the electrical parts box replacement
Low Pressure Sensor and High Pressure Sensor Disassembling
Upload a photo of the service panel before removal
Service panel removed
Upload a photo of the top panel before removal
Top panel removed
Upload a photo of the side panel (R) before removal
Side panel (R) removed
Connector 63LS (blue) and the 63HS(white) disconnected
Upload a photo of the clamps before loosening
Clamps loosened
LEV Disassembling
Remove the service panel
Upload a photo of the removed service panel
Remove the top panel
Upload a photo of the removed top panel
Remove the electrical parts box
Remove the LEV coil
Recover refrigerant
Note: Recover refrigerant without spreading it in the air
Remove the welded part of LEV
Access the parts list for your equipment in MaintainX.
Joint
CMY-Y62-G-E
Header
CMY-Y64/68-G-E
Joint
CMY-Y62-G-E
Header
CMY-Y64/68-G-E
Joint
CMY-Y62-G-E
Header
CMY-Y64/68-G-E
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













