

Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

A.O. Smith Gas Water Heater BTRC365
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
6 Monthly Storage Tank Flushing
Draining the Water Heater Storage Tank
Turn off the electrical supply to the water heater
Turn off the gas supply at the Main Gas Shutoff Valve if the water heater is going to be shut down for an extended period
Ensure the cold water inlet valve is open
Open a nearby hot water faucet and let the water run until the water is no longer hot
Close the cold water inlet valve to the water heater
Connect a hose to the water heater drain valve and terminate it to an adequate drain
Open the water heater drain valve and allow all the water to drain from the storage tank
Close the water heater drain valve when all water in the storage tank has drained
Initial 3 Years Anode Rod Inspection
CAUTION: Property Damage Hazard
Inspection Preparation
Ensure water heater is turned off and cooled down
Gather necessary tools for inspection
Anode Rod Inspection
Locate the anode rod on the water heater
Inspect the anode rod for corrosion or pitting
Is the anode rod corroded or pitted?
Post-Inspection Actions
Water Heater Deliming
Safety Precautions
Ensure all ignition sources are away from the faucet when turning on hot water.
Do not smoke or have open flame or sparks near the heater.
Do not mix UN•LIME with other chemicals.
Avoid contact with magnesium, aluminum, or galvanized metals.
Use rubber or neoprene gloves, especially if you have open sores or cuts.
Prepare the Water Heater
Turn off fuel and/or power supply to the heater.
Open hot water side of faucet closest to heater and allow water to run until cool.
1 Yearly Anode Rod Inspection
CAUTION: Property Damage Hazard
Inspection Preparation
Ensure water heater is turned off and cooled down
Gather necessary tools for inspection
Anode Rod Inspection
Locate the anode rod on the water heater
Inspect the anode rod for corrosion or pitting
Is the anode rod corroded or pitted?
Is the water artificially softened?
6 Monthly Temperature-Pressure Relief Valve Check
Safety Precautions
Ensure the following safety measures are in place
Use care when operating valve as the valve may be hot
Valve Operation Check
Lift the lever at the end of the valve several times to ensure it seats properly and operates freely
Did the valve reset completely after manual operation?
Post-Check Actions
Is the valve continuing to release water after manual operation?
Describe any issues observed during the check
Access the parts list for your equipment in MaintainX.
NSF Leg Kit
9003425205
UN•LIME(Deliming Solvent, 1 Gallon)
9005416105
UN•LIME(Deliming Solvent, 5 Gallons)
9005417105
Plate Gasket
9004099215
Two Unit Manifold Kit
9003426205
NSF Leg Kit
9003425205
UN•LIME(Deliming Solvent, 1 Gallon)
9005416105
UN•LIME(Deliming Solvent, 5 Gallons)
9005417105
Plate Gasket
9004099215
Two Unit Manifold Kit
9003426205
NSF Leg Kit
9003425205
UN•LIME(Deliming Solvent, 1 Gallon)
9005416105
UN•LIME(Deliming Solvent, 5 Gallons)
9005417105
Plate Gasket
9004099215
Two Unit Manifold Kit
9003426205
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













