

Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Leybold Vacuum Pump RUVAC WAU 501 EU
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
Initial 500 Hours Gear Box Oil Change
5.2 Oil Change/Gear Box
Ensure all safety precautions are observed
Use the oil-drain facility for safety and simplicity
Unscrew the oil-drain screws (11/2) or (11/1) and the oil-fill screw (11/4) to drain the oil
Clean the sealing surface and reinstall the oil-drain screw using a gasket in perfect condition
Wipe off any oil residues from the casing
Fill in new oil
Ensure the use of the correct oil type
Consult if using other oils or special lubricants
3000 Hourly Shaft Seal Housing Oil Change
5.3 Oil change/shaft seal housing
Observe all safety information provided in Section 5.1
Unscrew the oil-drain screw (10/3) under the shaft seal housing
Drain out the oil
Screw in the oil-drain screw using a gasket in perfect condition
Fill in fresh oil at the oiler (10/1)
Is the oil level for the shaft seal housing visible in the oiler?
Maximum level
Select the current state of the pump
Shaft Seal Replacement
5.8 Exchanging the Shaft Seals
Check the condition of the shaft seals and bushing
Is the oil level in the oiler dropping?
Is there oil under the shaft seal housing?
Diagnosis — inner shaft seal fault
Is the inner shaft seal faulty?
Switch off the pump immediately if the inner shaft seal is faulty
Repair the pump if the inner shaft seal is faulty
Diagnosis — outer shaft seal fault
Gear Box Oil Level Check
Operation Check
Check the oil level and condition in the oil level glass and oiler
Correct oil level and condition as required
Is the oil light-brown?
If the oil is dark, it may indicate early ageing due to high temperatures
Oil Level - Gear Box
Check oil level at vertical flow (center of oil-level glass when pump is not running)
Check oil level at horizontal flow (6 mm above center of oil-level glass)
Ensure oil level is not too low or too high to avoid inadequate lubrication or oil entering the pumping chamber
Pressure Balance Line Valve Cleaning
5.7 Cleaning the Valve of the Pressure Balance Line
Observe all safety information provided in Section 5.1
Remove the screws and take off the cover (12/1) with O-ring (12/2)
Take out the spring (12/4)
Remove the valve disk (12/6) with O-rings (12/5) and (12/7)
Check if the bushing (12/3) is damaged
Pull out and replace the bushing (12/3) if damaged
Clean all parts or replace them if necessary
Reassemble in the reverse sequence
Access the parts list for your equipment in MaintainX.
Shaft Seal Driver For WA/WAU 151/251/501
722 81027
Set Of Gaskets WA/WAU 501
194 64
Oil Drain Facility M 16 X 1,5 With Straight Drain Coupling
190 02
Oil Drain Facility M 16 X 1,5 With Right-Angled Drain Coupling
200 14 271
Diaphragm Pressure Switch SM 42 0,5 To 6 Mbar
164 05
Shaft Seal Driver For WA/WAU 151/251/501
722 81027
Set Of Gaskets WA/WAU 501
194 64
Oil Drain Facility M 16 X 1,5 With Straight Drain Coupling
190 02
Oil Drain Facility M 16 X 1,5 With Right-Angled Drain Coupling
200 14 271
Diaphragm Pressure Switch SM 42 0,5 To 6 Mbar
164 05
Shaft Seal Driver For WA/WAU 151/251/501
722 81027
Set Of Gaskets WA/WAU 501
194 64
Oil Drain Facility M 16 X 1,5 With Straight Drain Coupling
190 02
Oil Drain Facility M 16 X 1,5 With Right-Angled Drain Coupling
200 14 271
Diaphragm Pressure Switch SM 42 0,5 To 6 Mbar
164 05
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













