Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.

Documents & Manuals

Find all the essential guides in one place.

Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more

Work Order Templates

Pre-built workflows to keep your asset running smoothly.

Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more

Procedures

Integrate maintenance plans directly into your work orders.

Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more

Parts

Access the parts list for your equipment in MaintainX.

Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Inoxpa Valve VA47-0-77-06-52-080

Create an account to install this asset package.

Maintenance Plans for Inoxpa Valve Model VA47-0-77-06-52-080

Integrate maintenance plans directly into your work orders in MaintainX.

Control Head C-TOP S Adapter Kit Disassembly

Ensure the actuator is without pressure before starting

Disassembly

Release the compressed air supply

Remove the adapter and the air connection on the top part of the actuator

Screw the shaft (08A) on the top part of the piston with a 10 mm wrench

Insert the adapter (13) supplied with the kit through the shaft (08A)

Place the seals (20B, 20C, 20D) on the core (55)

Insert the core (55) in the adapter (13) and screw it on the actuator with a 19 mm wrench

Screw the air fitting (18) on the adapter (13)

Run this procedure

Manual Drive Assembly

Assembly

Place the discs (03,03A) in the open position.

Place the plugs (07A) on the valve half-bodies (02).

Place the handle guide (11) on the disc shaft (03).

Place the manual connecting rod (04) and the lever assembly connecting rod (04A) on the discs shafts (03,03A) and fix them with the screws (23D,23E).

Place the plugs (07B) on the manual connecting rod (04) and the lever assembly connecting rod (04).

Place the bushings (17D), the washers (25) and the drive arm (04B).

Place the nuts (26) and tighten them.

Run this procedure

Seal Seat Maintenance

Preparation

Ensure all parts are in perfect condition and free from any dirt.

Lubrication

Lubricate the disc shaft with the specified grease from chapter 8.2.1.

Lubricate the seat seal with the specified grease from chapter 8.2.1.

Assembly

Insert the long disc spindle into one of the seal holes.

Stretch the seal as shown in the drawing to insert the short spindle in the free gasket hole.

Turn the disc until it is perpendicular to the seal to facilitate assembly in the valve body.

Run this procedure

Leakeage Butterfly Valve Assembly

Safety Precautions

Proceed with caution to avoid personal injury.

Disconnect the compressed air before starting to disassemble the valve.

Read instructions carefully before disassembling the valve clamps.

Ensure only qualified persons perform valve and actuator assembly and disassembly.

Required Tools

Gather the necessary tools for disassembly and assembly

Assembly Procedure

Lubricate the discs (03,03A) and the seat seals (05) with the specified grease.

Run this procedure

Pneumatic Drive Assembly

Initial Assembly Steps

Place the discs (03,03A) in the open position.

Place the actuator connecting rod (04C) on the disc shaft (03A) as shown in the figure 10.011.32.0018.

Place the connecting rod (04D) on the disc shaft (03) as shown in the figure 10.011.32.0018 and fix it with the screw (23H).

Place the bushings, washers, and drive arm

Place the nuts (26) and tighten them.

Actuator and Support Installation

Supply compressed air to the actuator.

Place the support (21) and the actuator (10) on the actuator connecting rod (04C) and place the pin (50) which joins the connecting rod (04C) to the actuator (10).

Run this procedure