Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.

Documents & Manuals

Find all the essential guides in one place.

Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more

Work Order Templates

Pre-built workflows to keep your asset running smoothly.

Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more

Procedures

Integrate maintenance plans directly into your work orders.

Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more

Parts

Access the parts list for your equipment in MaintainX.

Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Mitsubishi Split-Type, Heat Pump Air Conditioner PUHZ-RP125VKA

Create an account to install this asset package.

Maintenance Plans for Mitsubishi Split-Type, Heat Pump Air Conditioner Model PUHZ-RP125VKA

Integrate maintenance plans directly into your work orders in MaintainX.

Outdoor Unit Compressor (MC) Replacement

Remove the service panel

Upload a photo of the removed service panel

Remove the top panel

Upload a photo of the removed top panel

Remove 2 front cover panel fixing screws (5 × 10) and remove the front cover panel

Upload a photo of the removed front cover panel

Remove 4 back cover panel fixing screws (5 × 10) and remove the back cover panel

Remove the electrical parts box

Upload a photo of the removed electrical parts box

Run this procedure

Outdoor Unit Thermistor <Outdoor pipe> (TH3) (TH33) and Thermistor <Discharge> (TH4), Thermistor <Shell> (TH32) Replacement

Remove the service panel

Disconnect the connectors, TH3 (white) and TH4 (white), TH33 (yellow), TH32 (black) on the controller circuit board in the electrical parts box

Loosen the clamp for the lead wire under the electrical parts box

Pull out the thermistor <Outdoor pipe> (TH3), (TH33) and thermistor <Discharge> (TH4) from the sensor holder

Removing the thermistor<Shell> (TH32)

Remove the sound proof cover (upper) for compressor

Pull out the thermistor <Shell> (TH32) from the holder of the compressor shell

Upload a photo of the completed task

Sign off on the thermistor replacement

Run this procedure

Outdoor Unit Power Receiver Replacement

Remove the service panel

Upload a photo of the removed service panel

Remove the top panel

Upload a photo of the removed top panel

Remove 2 front cover panel fixing screws (5 × 10) and remove the front cover panel

Upload a photo of the removed front cover panel

Remove 4 back cover panel fixing screws (5 × 10) and remove the back cover panel

Remove the electrical parts box

Upload a photo of the removed electrical parts box

Run this procedure

Outdoor Unit LEV Replacement

Warning: This procedure requires trained personnel with PPE!

Upload a photo of the service panel before removal

Service panel removed successfully?

Upload a photo of the top panel before removal

Top panel removed successfully?

Upload a photo of the electrical parts box before removal

Electrical parts box removed successfully?

Valve bed removed successfully?

Upload a photo of the right side panel before removal

Run this procedure

Outdoor Unit Thermistor <Oundoor 2-phase pipe> (TH6) Replacement

Warning: Ensure the unit is powered off before starting the procedure.

Upload a photo of the service panel before removal

Service panel removed

Upload a photo of the top panel before removal

Top panel removed

Connector TH7/6 (red) on the controller circuit board disconnected

Clamp for the lead wire in the rear of the electrical parts box loosened

Thermistor <Outdoor 2-phase pipe> (TH6) pulled out from the sensor holder

Note: In case of replacing thermistor <Outdoor 2-phase pipe> (TH6), replace it together with thermistor <Outdoor> (TH7) since they are combined together.

Run this procedure