

Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Goodman Gas Furnace GMVC960403BN
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
Pressure Regulator Adjustment
CAUTION
Connect a manometer to the outlet tap at the gas valve before adjusting the pressure regulator.
Ensure the final manifold pressure does not vary more than plus or minus 3 inches water column from the specified values for each gas type.
Pressure Regulator Adjustment
Turn the regulator clockwise to increase pressure and input.
Turn the regulator counterclockwise to decrease pressure and input.
Propane Gas Specific Instructions
Ensure no unit gas valve regulator is used with propane gas.
Adjust the second stage supply line pressure regulator to give 10" water column with all other gas consuming appliances running.
1 Yearly Furnace Inspection
WARNING: HIGH VOLTAGE
Disconnect all power sources before servicing or installing the unit.
Inspect the following furnace components for proper working order
Ignitor Handling Precautions
Was the ignitor handled with care, avoiding bare fingers, rough handling, or vibration?
Describe any issues found with the ignitor
Post Inspection Actions
Were all necessary repairs or services performed?
Technician's signature
Electronic Air Cleaner Inspection
Pre-Inspection Setup
Ensure the air cleaner is installed in the correct position
Is the air cleaner readily accessible for inspection?
Electronic Air Cleaner Inspection
Inspect and clean the following components
Media Air Cleaner Inspection
Inspect and replace the Media Air Cleaner filter cartridge if necessary
Check availability of replacement filter cartridges
Carbon Filters Inspection
2 Monthly Filter Replacement
WARNING: HIGH VOLTAGE
Disconnect all power before servicing, removing the filter or performing any other maintenance.
Check for multiple power sources
Filter Maintenance Importance
Ensure filters are cleaned or replaced every two months.
Is the filter of the same type and size as the one being replaced?
Media Air Filter or Electronic Air Cleaner Removal
Follow the manufacturer’s directions for service.
Upright Counterflow Filter Removal
Heating Performance Test
Preparation
Ensure all other gas appliances are turned off
Ensure the heating cycle has been in operation for at least fifteen minutes
Gas Meter Reading
Clock the gas meter to determine the time for one complete revolution of the cubic foot dial
Enter the time in seconds for one complete revolution of the cubic foot dial
Calculate BTU Input
Enter the number of cubic feet of gas consumed per hour (from gas rate chart)
Enter the calorific value of the gas (BTU per cubic foot)
Access the parts list for your equipment in MaintainX.
Communicating Thermostat Kit
CTK01AA
Communicating Thermostat Kit
CTK01BA
Communicating Thermostat Kit
CTK02
Communicating Thermostat Kit
CTK03AA
Communicating Thermostat Kit
CTK03AB
Communicating Thermostat Kit
CTK01AA
Communicating Thermostat Kit
CTK01BA
Communicating Thermostat Kit
CTK02
Communicating Thermostat Kit
CTK03AA
Communicating Thermostat Kit
CTK03AB
Communicating Thermostat Kit
CTK01AA
Communicating Thermostat Kit
CTK01BA
Communicating Thermostat Kit
CTK02
Communicating Thermostat Kit
CTK03AA
Communicating Thermostat Kit
CTK03AB
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













