

Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Goodman Gas Furnace AMVC960603BN
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
Electronic Air Cleaner Inspection
Pre-Inspection Setup
Ensure the air cleaner is installed in the correct position (not with the access door facing down).
Verify the air cleaner is located in the return air duct next to the blower compartment.
Electronic Air Cleaner Inspection
Inspect the accessibility of the electronic air cleaner for periodic inspection and cleaning.
Check the pre-filters and electronic cells for cleanliness.
Media Air Cleaner Inspection
Inspect the accessibility of the media air cleaner for periodic inspection and replacement of the filter cartridge.
Verify the availability of the following filter cartridges
Heating Performance Test
Preparation
Ensure all other gas appliances are turned off
Ensure the heating cycle has been in operation for at least fifteen minutes
Gas Meter Clocking
Record the time (in seconds) for one complete revolution of the cubic foot dial on the gas meter
BTU Input Calculation
Enter the number of cubic feet of gas consumed per hour
Enter the calorific value of the gas (BTU per cubic foot)
Calculate the BTU input by multiplying the cubic feet of gas consumed per hour by the calorific value
1 Yearly Furnace Inspection
WARNING
High Voltage Warning
Ignitor Handling Warning
Inspection Steps
Inspect the flue pipe system for blockage and/or leakage.
Inspect the outside termination and connections of the flue pipe system.
Inspect the combustion air intake pipe system for blockage and/or leakage.
Inspect the outside termination and connection of the combustion air intake pipe system.
Inspect the heat exchanger for corrosion and/or buildup within the passageways.
Pressure Regulator Adjustment
CAUTION
Connect a manometer to the outlet tap at the gas valve before adjusting the pressure regulator.
Pressure Regulator Adjustment
Measure the current manifold pressure for natural gas.
Is the manifold pressure within 3.5 inches water column for natural gas?
Measure the current manifold pressure for propane gas.
Is the manifold pressure within 10 inches water column for propane gas?
Turn the pressure regulator clockwise to increase pressure and input.
Turn the pressure regulator counterclockwise to decrease pressure and input.
2 Monthly Filter Replacement
WARNING: HIGH VOLTAGE
Disconnect all power before servicing, removing the filter or performing any other maintenance.
Check for multiple power sources
Filter Maintenance
Is the filter permanent?
Is the filter disposable?
Clean the permanent filter if applicable.
Replace the disposable filter if applicable.
Filter Removal Procedure
Access the parts list for your equipment in MaintainX.
Communicating Thermostat Kit
CTK01AA
Communicating Thermostat Kit
CTK01BA
Communicating Thermostat Kit
CTK02
Communicating Thermostat Kit
CTK03AA
Communicating Thermostat Kit
CTK03AB
Communicating Thermostat Kit
CTK01AA
Communicating Thermostat Kit
CTK01BA
Communicating Thermostat Kit
CTK02
Communicating Thermostat Kit
CTK03AA
Communicating Thermostat Kit
CTK03AB
Communicating Thermostat Kit
CTK01AA
Communicating Thermostat Kit
CTK01BA
Communicating Thermostat Kit
CTK02
Communicating Thermostat Kit
CTK03AA
Communicating Thermostat Kit
CTK03AB
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













