Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.

Documents & Manuals

Find all the essential guides in one place.

Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more

Work Order Templates

Pre-built workflows to keep your asset running smoothly.

Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more

Procedures

Integrate maintenance plans directly into your work orders.

Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more

Parts

Access the parts list for your equipment in MaintainX.

Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Kenworth Truck Company Vehicle T-880

Create an account to install this asset package.

Maintenance Plans for Kenworth Truck Company Vehicle Model T-880

Integrate maintenance plans directly into your work orders in MaintainX.

3 Monthly Air Conditioner Filter Maintenance

Tilt the hood open

Locate air intake housing

Remove filter cover

Inspect the filter according to the maintenance interval schedule

Replace filter in housing

Replace the filter cover on the air intake housing

Close and secure hood of vehicle

Sign off on the air conditioner filter maintenance

Run this procedure

Vehicle Maintenance

First 50-100 mi / 80-160 km

Wheel Mounting

• Refer to Wheels on page 332 for maintenance instructions.

First 500 mi / 800 km

11 Ensure that all maintenance intervals leading up to this point are repeated during this interval prior to the completion of those listed here.

First 500 mi / 800 km

Front Axle U-Bolt Torque

• Refer to Suspension U-Bolts, Class 10.9 on page 339 for maintenance instructions.

Run this procedure

2 Yearly Eaton Axle Lubrication

Warning: This procedure requires trained personnel with PPE!

Is the axle an Eaton axle?

If not, stop the procedure and report to the maintenance team

Enter the mileage of the vehicle

If mileage is between 3,000-5,000 miles, the original mineral-based lubricant must be drained

Is the axle factory filled with an Eaton-approved synthetic lubricant?

If yes, no initial drain is required

If converting to an Eaton-approved synthetic lube, drain the mineral-based lubes within the first 5,000 miles

Change the lubricant within the first 5,000 miles of operation after a carrier head replacement, regardless of the lubricant type

Run this procedure

1 Monthly Vehicle Maintenance

Check the kingpin lock and plate for wear and function

Check for proper function of Front Suspension - Spring Pins

Check the general condition and the tightness of the nuts of Front Suspension - U-bolts

Check oil level of Drive Axle - Vocational (PACCAR) - Axle Assembly

Visually inspect for damage or leaks in Drive Axle - Vocational (PACCAR) - Axle Assembly

Check the operation of Drive Axle - Vocational (PACCAR) - Breather

Check the 'cold' fill level at the differential carrier plug for a pinion angle of less than 7 degrees, or at the axle bowl plug for a pinion angle of greater than 7 degrees in Drive Axle (Meritor City Delivery / OFF HIGHWAY) - Axle Housing

Visually inspect for damage or leaks in Drive Axle (Meritor City Delivery / OFF HIGHWAY) - Axle Housing

Check the operation of Drive Axle (Meritor City Delivery / OFF HIGHWAY) - Breather

Run this procedure

6 Monthly Vehicle Maintenance

Front Axle - Linehaul (PACCAR) - Kingpin Joint Grease/Tie Rod Ends

Frame - Fifth Wheel

Frame - Engine Mounting

Front Axle - Vocational (PACCAR) - Steer Axle Wheel Ends: Oil Bath (Adjusted)

Front Axle - Vocational (PACCAR) - Steer Axle Semi-fluid (Adjusted)

Front Axle - Vocational (PACCAR) - Steer Axle Grease Pack (Adjusted)

Front Suspension - Front Spring

Front Suspension - Spring Pins and Shackles