Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more
John Deere Tractor 6130M
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
Yearly Maintenance
Inspect seat belt for damage and ensure proper working order
Use coolant test strips to check engine coolant
Inspect hydraulic hoses
Engine - Check drive belt for wear (or every 500 hours, whichever occurs first)
Change engine oil (or every 500 hours, whichever occurs first)
Front loader mounting frame - Check torques of fixing screws (see operator's manual and installation instructions of the front loader)
Change activated carbon filters of cab, if equipped (or every 500 hours, whichever occurs first)
Engine - Air cleaner, change the primary element (whenever the yellow Caution light flashes and corresponding information is displayed, or every 1500 hours) (2 yearly)
Air brake system - Change the air-drier cartridge (an earlier change may be necessary if condensed water drains out when checking compressed air tank, or every 1500 hours) (2 yearly)
750 Hourly Maintenance
Engine Maintenance
Replace filter on crankcase ventilation (oil separator)
Transmission/Hydraulic Oil Filters Replacement
Unscrew filter elements
Coat sealing rings of new filter elements with grease and screw in filter elements
Note: Use original John Deere filter elements only!
Run the engine briefly and operate several hydraulic functions. Shut off engine.
Wait for 10 to 15 minutes before checking the oil level. It must be between the marks on the sight-glass. If not, correct oil level.
Front-wheel drive axle - Final drives and disk brake, oil change
250 Hourly Maintenance
Retrieve the diagnostic trouble codes, rectify errors, and then delete the diagnostic trouble codes
Check neutral start circuit
Tractors with SyncroPlus™ transmission: Check if the starting motor does not turn over in all gears
Tractors with PowrReverser™ transmission: Check if the starting motor does not turn over in all travel directions
Tractors with PowrQuad™ transmission: Check if the starting motor does not turn over in both 'forward' and 'reverse' positions
PTO actuation - Check safety circuit
Lights - Check settings of headlights
Load center - Visually inspect and clean
Fuel system - Drain water and sediment from fuel tank
100 Hourly Maintenance
Retrieve the diagnostic trouble codes
Rectify errors
Delete the diagnostic trouble codes
Check that all lights and headlights are functioning properly
Check torques of fixing screws on Cab support
Check torque on attaching screws on Drawbar
Check torque on attaching screws on Height-adjustable trailer hitch
Check torques of attaching screws on Trailer hitch
Check torque on attaching screws on Pick-up hitch
2000 Hourly Maintenance
Engine Maintenance
Glow plugs checked by John Deere™ dealer
Valves adjusted by John Deere™ dealer (3000 Hourly)
Air Cleaner Maintenance
Secondary element of air cleaner changed (no later than at every fourth change of the primary element or every 5 years) (4500 Hourly)
Cooling System Maintenance
Coolant changed (if COOL-GARD™ II is used and coolant is checked annually)(6000 Hourly)
Front-wheel Drive Axle Maintenance
Accumulator of TLS™ changed by your John Deere™ dealer (10000 Hourly)
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX