

Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Branson Ultrasonics Ultrasonic Vapor Degreaser B1950
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
1 Daily Separator Cleaning
Warning: Follow local regulations for disposal of residue.
Separator/desiccator installed as a separator?
If not, do not proceed with the procedure.
Water separator water drain opened?
Discharge collected into a container?
Water separator water drain closed after flow stops?
Amount of dissolved or suspended solvent in the discharge
Sign off on the daily separator cleaning
6 Monthly Pump Lubrication
Warning: Ensure the pump is turned off and disconnected from power source before starting the procedure.
Is the pump motor properly lubricated with machine oil?
Does the vertical air cylinder require lubrication?
If yes, follow the steps below to lubricate the cylinder.
Raise the lift to the fully up position
Remove the top air hose
Remove the top exhaust flow control valve
Place one or two squirts from an oil can into the port
Replace the flow control valve and air hose
Controller Replacement
Warning: Disconnect the degreaser from electrical power before starting the procedure.
Degreaser disconnected from electrical power?
To replace the control or relay board
All wires transferred to the new board?
Mounting screws removed?
New board replaced?
Screws reinstalled?
To replace the control board
Voltage Switch (SW1) placed in the 230V position?
Degreaser Cleaning
Boil Down
Is the CONTAMINATION WARNING Indicator lighted but the degreaser has not shut down on B/S TEMP FAULT?
Remove 2-3 inches of solvent from the ultrasonic sump.
Did you turn on the heat?
Did you monitor the level in the ultrasonic sump?
Did you allow the degreaser to boil until it shuts down on B/S TEMP FAULT or B/S LEVEL FAULT?
Did you drain the solvent from the boil sump?
Did you refill the degreaser using the solvent removed in the first step?
Cleanout Procedure
Degreaser Inspection
Warning: Ensure to wear appropriate safety gear during the inspection
Check for loosening of plumbing connections
Check for leaks in solvent systems
Upload a photo of the area where the leak is detected
Describe the location and severity of the leak
Check for dampness or cold spots caused by evaporative cooling
Select the method used for leak detection
Upload a photo of the leak detection method used
Describe the results of the leak detection method used
Access the parts list for your equipment in MaintainX.
Accumulator 5/8 ODF
CPN-513-013
Assy PCB S7040-12
100-242-269
Bag Desiccant B1950
CPN-163-037
Block Distribution All
CPN-103-007
Bracket Base Back B1950
CPN-657-650
Accumulator 5/8 ODF
CPN-513-013
Assy PCB S7040-12
100-242-269
Bag Desiccant B1950
CPN-163-037
Block Distribution All
CPN-103-007
Bracket Base Back B1950
CPN-657-650
Accumulator 5/8 ODF
CPN-513-013
Assy PCB S7040-12
100-242-269
Bag Desiccant B1950
CPN-163-037
Block Distribution All
CPN-103-007
Bracket Base Back B1950
CPN-657-650
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













