Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more
Sullair Portable Air Compressor 185DPQ CC 100-3185
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
50 Hour Compressor Air Filter Replacement
Loosen and remove the air filter and cover
Remove the primary and optional secondary elements
Clean the body, inside and out, with a damp cloth
Reinstall (if clean) or replace the secondary element if installed
Replace the new primary filter element
Reposition the cover and lock it into the position
Reset the filter restriction indicator (if equipped)
Sign off on the air filter replacement
50 Hour Compressor Air Filter Inspection
Inspect air filter element for any light leaks indicating damage
Inspect all gaskets and gasket contact surfaces of the housing for any damage
Store clean elements for later use in a clean container
After installing the element, inspect and tighten all air inlet connections before operating the compressor
250 Hour Compressor Maintenance
CAUTION: Operating the compressor below its minimum specified idle speed will damage the compressor. Operating the compressor in this condition will cause coupling and/or compressor failure
Clean the radiator and cooler exterior surfaces every 100 hours
Check the Engine Operator’s Manual for service requirements every 100 hours
Check fan belt tension
Clean the radiator and cooler exterior surfaces
Check the Engine Operator's Manual for service requirements
Change the engine oil and filter
Clean or replace the return line strainer
Change the air filter primary elements
1 Daily Compressor Maintenance
Check daily compressor prior to operation
WARNING: Do not use aerosol types of starting aids such as ether. Such use could result in an explosion and personal injury
Ensure that the compressor is on a level surface
Ensure that a minimum clearance of 3 feet [0.9 meters] is provided all the way around the machine to allow exhaust gas to ventilate before operating the machine
Check all oil and fluid levels in the engine and compressor. Add oil and/or fluid if necessary
Fill the fuel tank and drain any water from the fuel/ water separator
Check the dust collectors and clean if necessary
Crack open one service line
When the compressor is warmed up, press the "Start/Load" button to load the compressor for full operation
Initial 50 Hours Compressor Maintenance
Clean the return line orifice and check the strainer
Change the compressor fluid filter
Check the Engine Operator’s Manual for service requirements
Check the fuel filter for water
Confirm that the receiver tank cover bolts are tightened to 60 lbf ft (81 N m)
Sign off on the compressor maintenance
Access the parts list for your equipment in MaintainX.
All Weather Fluid
250030-757
All Weather Fluid
250030-758
Separator Element
88291009-563
All Weather Fluid
250030-757
All Weather Fluid
250030-758
Separator Element
88291009-563
All Weather Fluid
250030-757
All Weather Fluid
250030-758
Separator Element
88291009-563
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX