The Stryker Pneumo Sure High Flow Insufflator is a high-performance medical device designed for laparoscopic surgeries. This advanced insufflator ensures optimal gas flow and pressure control, enhancing surgical precision and patient safety. Ideal for healthcare facilities, it combines reliability with user-friendly features for efficient operation.

Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant

PDF MANUAL

Manual for Stryker Pneumo Sure High Flow Insufflator

MAINTENANCE RESOURCES

Complete asset maintenance, one click away

Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.

Documents & Manuals

Find all the essential guides in one place.

Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more

Work Order Templates

Pre-built workflows to keep your asset running smoothly.

Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more

Procedures

Integrate maintenance plans directly into your work orders.

Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more

Parts

Access the parts list for your equipment in MaintainX.

Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Stryker Pneumo Sure High Flow Insufflator

Create an account to install this asset package.

Maintenance Plans for Stryker Pneumo Sure High Flow Insufflatornull

Integrate maintenance plans directly into your work orders in MaintainX.

1 Year Gas Flow Rate Test

Warning: This test requires trained personnel with PPE!

Test setup with open connection, without connected insufflation tube.

Set a nominal gas flow rate of 15 l/min.

Start insufflation: Press the START function field.

Press the gas volume function field (o.0 | must be displayed).

Start measuring for one minute.

Stop the insufflation after one minute: Press the STOP function field.

Enter the gas consumption

Was the gas consumption at least 11-12 l?

Run this procedure

1 Year Insufflator Basic Function Test

Remove insufflation tube from device

Turn the device on using the On/Off switch

Set to High Flow operating mode

Check the displayed values

Start insufflation by pressing the START function field

Select the max. nominal gas flow

Stop insufflation by pressing the STOP function field

Press the gas volume function field

Check if the basic function test of the device is complete

Run this procedure

1 Year Insufflator Safety Test

Does the fuse correspond with the specifications indicated by the manufacturer?

Are labels and stickers on device legible?

Does the mechanical condition of the device allow for its safe use?

Is the device clean to ensure proper and safe functionality?

Measure leakage currents according to IEC 60601-1 / EN 60601-1

Measure protective conductor resistance according to IEC 60601-1 / EN 60601-1. The protective conductor resistance is measured while device is connected to the power supply. The max. value is 0.2 S.

Measure the insulation resistance with 500-700 V DC. The min. value is 50 MS

The electric strength with high voltage cannot be measured.

Sign off on the safety test

Run this procedure

1 Year Max. Device Pressure Test

Select operating mode

Select the max. nominal gas flow

Connect a manometer and an open Veress cannula to the insufflation tube connection/adapter.

Select the max. gas flow

Start insufflation: Press the START function field. The manometer registers a pulsing pressure increase.

Enter the maximum pressure registered by the manometer

Stop insufflation: Press the STOP function field.

Sign off on the pressure test

Run this procedure

1 Year Pressure Monitoring Test in High Flow Operating Mode

Set to High Flow operating mode

Set a nominal pressure of 15 mm Hg

Set a nominal gas flow of 3 l/min

Set a venting pressure of 3mm Hg in the Venting pressure limit configuration menu

Use the syringe to generate a pressure of at least 19 mm Hg, which registers on the manometer

Start insufflation by pressing the START function field. An acoustic warning sound is emitted with a pressure of more than 19 mm Hg (for 5 seconds) and the display depicts Overpressure

Reduce the pressure. The warning ends when the pressure falls below 19 mm Hg (nominal pressure plus 4 mm Hg). Stop insufflation by pressing the STOP function field

Use the syringe to generate a pressure of at least 30 mm Hg, which registers on the manometer

Start insufflation by pressing the START function field. An acoustic warning sound is emitted without delay in case pressure exceeds 30 mm Hg and the display depicts Overpressure

Run this procedure