Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.

Documents & Manuals

Find all the essential guides in one place.

Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more

Work Order Templates

Pre-built workflows to keep your asset running smoothly.

Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more

Procedures

Integrate maintenance plans directly into your work orders.

Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more

Parts

Access the parts list for your equipment in MaintainX.

Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Robopac Self-Propelled Stretch Wrapper Machine Robot S7

Create an account to install this asset package.

Maintenance Plans for Robopac Self-Propelled Stretch Wrapper Machine Model Robot S7

Integrate maintenance plans directly into your work orders in MaintainX.

10000 Hourly Steering Return Spring Replacement

Warning: This maintenance requires trained personnel with PPE!

Enter the machine's hour meter reading

Steering return spring in good condition?

If the spring is not in good condition, proceed with replacement

Upload a photo of the replaced spring

Sign off on the spring replacement

Run this procedure

200 Hourly Self-Propelled Stretch Wrapper Machine Maintenance

Clean Rubber rollers

Lubricate Film carriage

See 'Lubrication point diagram'

Spread grease over it

Check the lubricant level

Do not top up and/or change in life-lubed reduction units and gearmotors

Important: Observe the lubrication frequency to obtain the best performance and a longer machine’s operating life. Use lubricants (oils and greases) recommended by the Manufacturer or with similar chemical-physical features.

Check the chain tensioning Film carriage

See 'Film carriage lifting chain adjustment'

Run this procedure

40 Hourly Machine Working Area Cleaning

Warning: This cleaning procedure requires trained personnel with PPE!

Cycle timings have been defined on the basis of the standard cycle.

The standard cycle is the following: 500 mm high film reel, 1500 mm high pallet, pallet weight equal to 1500 kg, total wrapping cycle consisting of two turns at the base, two turns at the top with rotation speed of 12 r.p.m. or 80 m/1’ and carriage upstroke and downstroke speed equal to 4 m/1’.

Machine Working Areas cleaned?

Upload a photo of the cleaned machine working area

Sign off on the machine working area cleaning

Run this procedure

5000 Hourly Reduction Unit / Gearmotor Change

Warning: Follow the scheduled maintenance intervals for best performance, long operating life and safety.

Change the lubricant in reduction units and gearmotors.

Check the lubricant level.

Do not top up and/or change in life-lubed reduction units and gearmotors.

Important: Observe the lubrication frequency for best performance and longer machine’s operating life. Use recommended lubricants.

Cycle timings are based on the standard cycle: 500 mm high film reel, 1500 mm high pallet, pallet weight equal to 1500 kg, total wrapping cycle consisting of two turns at the base, two turns at the top with rotation speed of 12 r.p.m. or 80 m/1’ and carriage upstroke and downstroke speed equal to 4 m/1’.

Sign off on the 5000 Hourly Reduction Unit / Gearmotor Change

Run this procedure

Battery Replacement

Caution - warning: The main fuse of the machine is built into the battery cables, use only original cables.

Lift the battery casing (A)

Remove the connector (B) from the plug

Caution - warning: First disconnect the negative terminal (−)

Disconnect the terminals (C-D-E-F)

Extract the batteries (G) and replace them

Caution - warning: Respect the polarities when connecting the terminals. Grease the positive terminal (✚) and connect it first.

Reconnect the terminals (C-D-E-F)

Engage the connector (B) to the plug