Atlas Copco Air Dryer FX1160

Safety precautions: When handling refrigerant gas, all applicable safety precautions must be observed.

Contact of refrigerant with the skin will cause frostbite. Wear special gloves and, in case of skin contact, rinse with water. For no reason the clothes should be removed.

Refrigerant fluid can cause also freezing of the eyes; therefore, safety glasses must be worn.

Refrigerant is poisonous. Do not inhale refrigerant vapours. Check that the working area is adequately ventilated.

When the dryer is filled with refrigerant, it is forbidden to remove the refrigerant compressor inlet sensor.

When removing the side panels of the dryer, be aware that internal elements such as the pipes can reach a temperature of 120˚C (248˚F). Therefore, wait until the dryer has cooled down before removing the side panels.

Before starting any maintenance or repairs, switch off the voltage. Isolate the dryer from the air net and depressurize the unit following the pressure discharge procedure.

Brush or blow off the finned surface of the condenser regularly.

When handling refrigerant gas, all applicable safety precautions must be observed. The following points are stressed:

The condensate drain filter must be cleaned.

Close the inlet and outlet valves (1)

Remove the panel (2) and depressurize the dryer by pressing and holding down the “TEST” button located on the top of the drain (3)

Switch off the machine (pushing the “OFF” button) (4)

Disconnect the power supply (5)

Safety precautions: When handling refrigerant gas, all applicable safety precautions must be observed.

Contact of refrigerant with the skin will cause frostbite. Wear special gloves and, in case of skin contact, rinse with water. For no reason the clothes should be removed.

Refrigerant fluid can cause also freezing of the eyes; therefore, safety glasses must be worn.

Refrigerant is poisonous. Do not inhale refrigerant vapours. Check that the working area is adequately ventilated.

When the dryer is filled with refrigerant, it is forbidden to remove the refrigerant compressor inlet sensor.

When removing the side panels of the dryer, be aware that internal elements such as the pipes can reach a temperature of 120˚C (248˚F). Therefore, wait until the dryer has cooled down before removing the side panels.

Before starting any maintenance or repairs, switch off the voltage. Isolate the dryer from the air net and depressurize the unit following the pressure discharge procedure.

Wear kit drain (2200902017) replaced?

Safety precautions: When handling refrigerant gas, all applicable safety precautions must be observed.

Contact of refrigerant with the skin will cause frostbite. Wear special gloves and, in case of skin contact, rinse with water. For no reason the clothes should be removed.

Refrigerant fluid can cause also freezing of the eyes; therefore, safety glasses must be worn.

Refrigerant is poisonous. Do not inhale refrigerant vapours. Check that the working area is adequately ventilated.

When the dryer is filled with refrigerant, it is forbidden to remove the refrigerant compressor inlet sensor.

When removing the side panels of the dryer, be aware that internal elements such as the pipes can reach a temperature of 120˚C (248˚F). Therefore, wait until the dryer has cooled down before removing the side panels.

Before starting any maintenance or repairs, switch off the voltage. Isolate the dryer from the air net and depressurize the unit following the pressure discharge procedure.

Drain filter (0803501008) replaced

Sign off on the drain filter replacement

Safety precautions: When handling refrigerant gas, all applicable safety precautions must be observed.

Contact of refrigerant with the skin will cause frostbite. Wear special gloves and, in case of skin contact, rinse with water. For no reason the clothes should be removed.

Refrigerant fluid can cause also freezing of the eyes; therefore, safety glasses must be worn.

Refrigerant is poisonous. Do not inhale refrigerant vapours. Check that the working area is adequately ventilated.

When the dryer is filled with refrigerant, it is forbidden to remove the refrigerant compressor inlet sensor.

When removing the side panels of the dryer, be aware that internal elements such as the pipes can reach a temperature of 120˚C (248˚F). Therefore, wait until the dryer has cooled down before removing the side panels.

Before starting any maintenance or repairs, switch off the voltage. Isolate the dryer from the air net and depressurize the unit following the pressure discharge procedure.

Clean the condenser surface with an air flow from the inside towards the outside