MaintainX Asset Hub logo
EnterprisePricing
Thermo Fisher

Thermo Fisher Circulating Water Bath 2864

Need answers fast?
Explore the manual using AI.

Thermo Fisher Circulating Water Bath 2864
Thermo Fisher Circulating Water Bath 2864

Turn manuals into instant answers
with your AI-powered assistant
Turn manuals into instant answers
with your AI-powered assistant

PDF MANUAL

Manual for Thermo Fisher Circulating Water Bath 2864

MAINTENANCE RESOURCES

Complete asset maintenance, one click away

Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.

Documents

Documents & Manuals

Find all the essential guides in one place.

  • CheckTensioning Guide

  • CheckBelt-diagram

  • CheckC-120 pulleys

  • + 13 more

Work Orders

Work Order Templates

Pre-built workflows to keep your asset running smoothly.

  • CheckDaily Electrical System Inspection

  • CheckReplace Roller and Pulley

  • CheckInstall Engine B-120

  • + 29 more

Procedures

Procedures

Integrate maintenance plans directly into your work orders.

  • CheckMotion Industries

  • CheckApplied Industrial Technologies

  • CheckElectrical Brothers

  • + 5 more

Parts

Parts

Access the parts list for your equipment in MaintainX.

  • CheckDrive Motor

  • CheckB2 Rollers

  • CheckTensioning System

  • + 40 more

Thermo Fisher Circulating Water Bath 2864

Thermo Fisher Circulating Water Bath 2864

Create an account to install this asset package.

Maintenance Plans for Thermo Fisher Circulating Water Bath Model 2864

Integrate maintenance plans directly into your work orders in MaintainX.

CPU Or Display/Keyboard Board Replacement

Check mark

Board Removal

Check mark

Remove connectors from CPU board

Check mark

Remove connector J102 from power supply board with care to avoid bending pins

Check mark

Remove four nuts from CPU board and remove CPU board and Keyboard/Display board

Check mark

Remove J201 from CPU board with care to avoid bending pins

Check mark

Remove board

Check mark

Board Installation

Check mark

Reverse removal procedure to install new board

Check mark

Software Configuration

Run this procedureArrow right

Temperature Calibration

Check mark

Preparation

Check mark

Connect the temperature probe connector to J302 on CPU board

Check mark

Turn Power switch to the OFF position

Check mark

Entering Calibration Mode

Check mark

Press and hold the SETPOINT key while turning Power ON

Check mark

Press SETPOINT to end LED display test

Check mark

Enter 0012 on the display and press SETPOINT

Check mark

Calibration Process

Check mark

Ensure the unit is in Calibration mode and press SETPOINT

Run this procedureArrow right

Circulating Water Bath Cleaning

Check mark

General Cleaning

Check mark

Clean the bath with mild soapy water

Check mark

Rinse the bath with distilled water

Check mark

Add formaldehyde or quaternary ammonium germicide if algae or microorganisms are present

Check mark

Chemical Usage Precautions

Check mark

Ensure the following chemicals are never used

Check mark

Limit the use of necessary chemicals to a maximum of four hours

Check mark

Removing Discoloration

Check mark

Wear heavy gloves and goggles for protection

Run this procedureArrow right

Circulating Pump Replacement

Check mark

Preparation

Check mark

Drain water from bath

Check mark

Pump Removal

Check mark

Remove the two pump leads attached to power switch

Check mark

Remove green wire from pump to ground lug

Check mark

Loosen the two visible hose clamps with a screwdriver

Check mark

Remove tubing from pump

Check mark

Disconnect pump from pump bracket by removing two screws

Check mark

Remove pump from bath

Run this procedureArrow right

Heater Replacement

Check mark

Heater Removal

Check mark

Remove nuts and disconnect wires from heater leads

Check mark

Remove two hex nuts from heater ends using a 13/16" socket

Check mark

Remove heater

Check mark

Heater Installation

Check mark

Install new heater

Check mark

Reconnect wires and secure nuts

Check mark

Post Installation Check

Check mark

Is the heater securely installed?

Run this procedureArrow right

Parts for Thermo Fisher Circulating Water Bath 2864

Access the parts list for your equipment in MaintainX.

Part Name
Part Number

Quaternary Ammonium Germicide

3166250

Power Supply Pcb Assembly

3176677

Quaternary Ammonium Germicide

3166250

Power Supply Pcb Assembly

3176677

Quaternary Ammonium Germicide

3166250

Power Supply Pcb Assembly

3176677

Unlock efficiency
with MaintainX CoPilot

MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.

Time Lapse Icon

Reduce Unplanned Downtime

Ensure your team follows consistent procedures to minimize equipment failures and costly delays.

Wrench Clock Icon

Maximize Asset Availability

Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.

Dollar Coin Icon

Lower Maintenance Costs

Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.

Thousands of companies manage their assets with MaintainX

DuracellAB InBevErgonTitan AmericaMeritUnivar SolutionsRivianCadrexMagnaMaasPresriteSoutheast PowerInterrollDuracellAB InBevErgonTitan AmericaMeritUnivar SolutionsRivianCadrexMagnaMaasPresriteSoutheast PowerInterroll

More from Thermo Fisher

Explore Other Assets