Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.

Documents & Manuals

Find all the essential guides in one place.

Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more

Work Order Templates

Pre-built workflows to keep your asset running smoothly.

Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more

Procedures

Integrate maintenance plans directly into your work orders.

Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more

Parts

Access the parts list for your equipment in MaintainX.

Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Sullivan Air Compressor SP20-150

Create an account to install this asset package.

Maintenance Plans for Sullivan Air Compressor Model SP20-150

Integrate maintenance plans directly into your work orders in MaintainX.

50 Hourly / 1 Weekly Separator Element Change

6.2 GENERAL MAINTENANCE SAFETY

WARNING! Never assume a compressor is safe to work on just because it is not operating. It could restart at any time.

WARNING! Do not allow oil to accumulate on, in or around acoustic noise material. Immediately replace any oilsoaked material after cleaning enclosure surface with nonflammable solvent.

WARNING! Do not substitute bolts with material or markings different from the original equipment.

CAUTION! Do not over-tighten any bolt, nut fitting, connection or spin-on filter element.

CAUTION! Perform repairs and maintenance only in clean, dry conditions in a well-lit and ventilated area.

CAUTION! Clean up any spilled oil or oil leakage and repair oil leaks as soon as they are discovered.

6.3 STOPPING FOR MAINTENANCE

Disconnect and lockout the main power source.

Run this procedure

12000 Hourly Pal-Extra 68 Lubricant Change

6.2 GENERAL MAINTENANCE SAFETY

WARNING! Never assume a compressor is safe to work on just because it is not operating. It could restart at any time.

WARNING! Do not allow oil to accumulate on, in or around acoustic noise material. Immediately replace any oilsoaked material after cleaning enclosure surface with nonflammable solvent.

WARNING! Do not substitute bolts with material or markings different from the original equipment.

CAUTION! Do not over-tighten any bolt, nut fitting, connection or spin-on filter element.

CAUTION! Perform repairs and maintenance only in clean, dry conditions in a well-lit and ventilated area.

CAUTION! Clean up any spilled oil or oil leakage and repair oil leaks as soon as they are discovered.

6.3 STOPPING FOR MAINTENANCE

Per Occupational Safety & Health Administration (OSHA) regulation 1910.147: The Control of Hazardous Energy Source (Lockout/Tagout), disconnect and lockout the main power source.

Run this procedure

8000 Hourly Air Compressor Maintenance

6.2 GENERAL MAINTENANCE SAFETY

WARNING! Never assume a compressor is safe to work on just because it is not operating. It could restart at any time.

WARNING! Do not allow oil to accumulate on, in or around acoustic noise material. Immediately replace any oilsoaked material after cleaning enclosure surface with nonflammable solvent.

WARNING! Do not substitute bolts with material or markings different from the original equipment.

CAUTION! Do not over-tighten any bolt, nut fitting, connection or spin-on filter element.

CAUTION! Perform repairs and maintenance only in clean, dry conditions in a well-lit and ventilated area.

CAUTION! Clean up any spilled oil or oil leakage and repair oil leaks as soon as they are discovered.

6.3 STOPPING FOR MAINTENANCE

Per Occupational Safety & Health Administration (OSHA) regulation 1910.147: The Control of Hazardous Energy Source (Lockout/Tagout), disconnect and lockout the main power source.

Run this procedure

2000 Hourly Air Compressor Maintenance

6.2 GENERAL MAINTENANCE SAFETY

Compressor safe to work on?

Oil accumulation on, in or around acoustic noise material?

Bolts with material or markings different from the original equipment?

Repairs and maintenance performed in clean, dry conditions in a well-lit and ventilated area?

Spilled oil or oil leakage cleaned up and repaired?

6.3 STOPPING FOR MAINTENANCE

Main power source disconnected and locked out?

Compressor isolated from the compressed air supply?

Run this procedure

500 Hourly / 3 Monthly Oil / After Cooler Fins Inspection

6.2 GENERAL MAINTENANCE SAFETY

WARNING! Never assume a compressor is safe to work on just because it is not operating. It could restart at any time.

WARNING! Do not allow oil to accumulate on, in or around acoustic noise material. Immediately replace any oilsoaked material after cleaning enclosure surface with nonflammable solvent.

WARNING! Do not substitute bolts with material or markings different from the original equipment.

CAUTION! Do not over-tighten any bolt, nut fitting, connection or spin-on filter element.

CAUTION! Perform repairs and maintenance only in clean, dry conditions in a well-lit and ventilated area.

CAUTION! Clean up any spilled oil or oil leakage and repair oil leaks as soon as they are discovered.

6.3 STOPPING FOR MAINTENANCE

Per Occupational Safety & Health Administration (OSHA) regulation 1910.147: The Control of Hazardous Energy Source (Lockout/Tagout), disconnect and lockout the main power source.

Run this procedure