Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

Chromalox Circulating Water Temperature Control System CMX-250-12-480
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
Pump Replacement
Safety Precautions
Disconnect all power to the system
Bleed pressure and drain all water from the system
Panel and Wiring Removal
Remove top and side panels
Remove pump motor wiring cover panel (2 screws)
Note location of pump motor wires and remove
Pump Motor Removal
Loosen and remove vent line
Heat Exchanger Replacement
!Warning: HAZARD OF ELECTRIC SHOCK. Disconnect all power and piping to system.
Preparation
Disconnect all power to the system
Bleed pressure and drain all water from the system
Removal of Old Heat Exchanger
Remove top panel
Remove cover on the cooling solenoid
Disconnect 'COOLING INLET' and 'COOLING OUTLET' piping
Disconnect copper tubing connected to the heat exchanger
Circulating Water Temperature Control Unit Maintenance
Safety Precautions
Disconnect all power before servicing or performing maintenance.
Ensure the system is not operating or hot before servicing.
Verify maintenance is performed by qualified personnel only.
Shut Down Procedure
Set the temperature controller setpoint to 90°F or lower. Allow to cool.
Turn off power to the unit. The controller will turn off.
Turn off the water supply to the unit.
Disconnect electrical supply to the unit.
Heater Replacement
Warning: HAZARD OF ELECTRIC SHOCK. Disconnect all power and piping to system.
Preparation
Disconnect all power to the system.
Bleed pressure and drain all water from the system.
Heater Removal
Remove top panel.
Remove red top cover on the heater (see Figure 6.2, Heater/Chamber Photo).
Note location of wires on the heater, then remove wires (L1, L2, L3).
Loosen compression fitting on the heater power supply cable.
Access the parts list for your equipment in MaintainX.
3/4 Hp Motor 240V/480V
193-121843-227
Solenoid Valve
344-121780-012
Pressure Relief Valve
344-048419-004
Automatic Air Vent
344-053181-001
Pressure Gauge
130-118661-021
3/4 Hp Motor 240V/480V
193-121843-227
Solenoid Valve
344-121780-012
Pressure Relief Valve
344-048419-004
Automatic Air Vent
344-053181-001
Pressure Gauge
130-118661-021
3/4 Hp Motor 240V/480V
193-121843-227
Solenoid Valve
344-121780-012
Pressure Relief Valve
344-048419-004
Automatic Air Vent
344-053181-001
Pressure Gauge
130-118661-021
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













