

Turn manuals into instant answers
with your AI-powered assistantTurn manuals into instant answers
with your AI-powered assistant
Get instant access to all the maintenance information you need. Empower technicians to perform preventive maintenance with asset packages, ready to use right out of the box.
Find all the essential guides in one place.
Tensioning Guide
Belt-diagram
C-120 pulleys
+ 13 more
Pre-built workflows to keep your asset running smoothly.
Daily Electrical System Inspection
Replace Roller and Pulley
Install Engine B-120
+ 29 more
Integrate maintenance plans directly into your work orders.
Motion Industries
Applied Industrial Technologies
Electrical Brothers
+ 5 more
Access the parts list for your equipment in MaintainX.
Drive Motor
B2 Rollers
Tensioning System
+ 40 more

SEW eurodrive Electric Motor DT71D2
Create an account to install this asset package.
Integrate maintenance plans directly into your work orders in MaintainX.
2 Yearly Brake Inspection
8.1 Inspection and maintenance intervals
Use only genuine spare parts in accordance with the valid parts list
Install a new brake control system when replacing the brake coil
Ensure motors are not hot to avoid burns
Secure hoist drives or lower them to prevent falling
Isolate the motor and brake from the supply to prevent unintentional power-up
Brake types applicable for inspection
Calculate required inspection/maintenance intervals based on project planning documents
Inspection Procedure
10000 Hourly Motor Maintenance
8.1 Inspection and maintenance intervals
Isolate the motor and brake from the supply before starting work, safeguarding them against unintentional power-up
Inspect the motor
8.3 Inspection / maintenance on the motor
Remove the forced cooling fan and encoder, if installed
Remove flange or fan guard and fan
Remove the hex head bolt from the drive end bearing end shield and the non-drive end bearing end shield, release the stator from the drive end bearing end shield
For motors with BM/BMG brake: open the terminal box cover, unfasten the brake cable from the rectifier; push the non-drive end bearing end shield and the brake off the stator and carefully lift them off
For motors with BMG02, BR03 brake: remove the complete brake with the releasing lever
Anticorrosion Coating Maintenance
8.1 Inspection and maintenance intervals
Check external factors affecting the drive
Is the current anticorrosion coating intact?
Touch up the surface coating if necessary
Renew the anticorrosion coating if required
Initial Startup Check
6.1 Prerequisites for startup
Before startup, ensure the following conditions are met
During startup, ensure the following conditions are met
3000 Hourly Brake Inspection
8.1 Inspection and maintenance intervals
Ensure the following safety precautions are taken
Inspect the following brake components
BMG02 Brake Inspection (Sec. 8.4)
Isolate the motor and brake from the supply, safeguarding them against unintentional power-up
Unscrew the hand lever, remove the fan guard and the fan
Loosen the screws and remove the complete brake with the releasing lever
Measure the thickness 'd' of the brake disk
Is the brake disk thickness above the minimum value?
Access the parts list for your equipment in MaintainX.
Carrier Plate For Installation Integrated In The Motor According To The ECOFAST Specification; Obtain From SEW-EURODRIVE
0187 390 3
BMG02 Brake 24 VDC 0.8 Nm
0574 319 2
BMG02 Brake 24 VDC 1.2 Nm
0574 323 0
BMG02/HR Brake 24 VDC 0.8 Nm
0574 327 3
BMG02/HR Brake 24 VDC 1.2 Nm
0574 331 1
Carrier Plate For Installation Integrated In The Motor According To The ECOFAST Specification; Obtain From SEW-EURODRIVE
0187 390 3
BMG02 Brake 24 VDC 0.8 Nm
0574 319 2
BMG02 Brake 24 VDC 1.2 Nm
0574 323 0
BMG02/HR Brake 24 VDC 0.8 Nm
0574 327 3
BMG02/HR Brake 24 VDC 1.2 Nm
0574 331 1
Carrier Plate For Installation Integrated In The Motor According To The ECOFAST Specification; Obtain From SEW-EURODRIVE
0187 390 3
BMG02 Brake 24 VDC 0.8 Nm
0574 319 2
BMG02 Brake 24 VDC 1.2 Nm
0574 323 0
BMG02/HR Brake 24 VDC 0.8 Nm
0574 327 3
BMG02/HR Brake 24 VDC 1.2 Nm
0574 331 1
MaintainX CoPilot is your expert colleague, on call 24/7, helping your team find the answers they need to keep equipment running.
Reduce Unplanned Downtime
Ensure your team follows consistent procedures to minimize equipment failures and costly delays.
Maximize Asset Availability
Keep your assets running longer and more reliably, with standardized maintenance workflows from OEM manuals.
Lower Maintenance Costs
Turn any technician into an expert to streamline operations, maintain more assets, and reduce overall costs.
Thousands of companies manage their assets with MaintainX













