Quarterly PM Applicator

Check oil in gearbox.

Inspect chains and sprockets for wear, alignment, and proper tension.

Remove any yarn from rollers and roller shafts.

Inspect roller headers for cracks, or any signs of wear / damage.

Inspect roller shafts for wear in /around the bearing.

Check all bearing set screws, tighten if necessary.

Grease all bearings, wipe excess grease off of grease fitting an bearing.

Inspect blue wrap on pull roller for wear.

Load Cell Roller

Remove any yarn from rollers and roller shafts.

NOTE Follow these steps for the roller above and below the load cell roller.

Inspect roller headers for cracks, or any signs of wear / damage.

Inspect roller shafts for wear in /around the bearing.

Check all bearing set screws, tighten if necessary.

Grease all bearings, wipe excess grease off of grease fitting an bearing.

Traverse

Remove guard from right side frame, above electrical panel.

Check oil in gearbox.

Inspect chains and sprockets for wear, alignment, and proper tension.

Inspect belts and pulleys for wear, alignment, and proper tension.

Inspect v-groove wheels and traverse rails for damage and wear.

Right Side End Dam

Check oil in gearbox.

Inspect v-groove wheels and traverse rails for damage / wear.

Physically inspect bronze nut and screwbar for damage and wear by attempting to move the screwbar within the nut.

Visually inspect the bronze nut and screwbar for damage or wear. If excessive bronze shavings are presentunder the nut, remove and disassemble the nut for furthur inspection.

Left Side End Dam

Check oil in gearbox.

Inspect v-groove wheels and traverse rails for damage / wear.

Physically inspect bronze nut and screwbar for damage and wear by attempting to move the screwbar within the nut.

Visually inspect the bronze nut and screwbar for damage or wear. If excessive bronze shavings are present under the nut, remove and disassemble the nut for furthur inspection.

Quarterly PM Applicator

Quarterly PM Applicator

Pull Roller

Check oil in gearbox.

Inspect chains and sprockets for wear, alignment, and proper tension.

Remove any yarn from rollers and roller shafts.

Inspect roller headers for cracks, or any signs of wear / damage.

Inspect roller shafts for wear in /around the bearing.

Check all bearing set screws, tighten if necessary.

Grease all bearings, wipe excess grease off of grease fitting an bearing.

Inspect blue wrap on pull roller for wear.

Load Cell Roller

Remove any yarn from rollers and roller shafts.

NOTE Follow these steps for the roller above and below the load cell roller.

Inspect roller headers for cracks, or any signs of wear / damage.

Inspect roller shafts for wear in /around the bearing.

Check all bearing set screws, tighten if necessary.

Grease all bearings, wipe excess grease off of grease fitting an bearing.

Traverse

Remove guard from right side frame, above electrical panel.

Check oil in gearbox.

Inspect chains and sprockets for wear, alignment, and proper tension.

Inspect belts and pulleys for wear, alignment, and proper tension.

Inspect v-groove wheels and traverse rails for damage and wear.

Right Side End Dam

Check oil in gearbox.

Inspect v-groove wheels and traverse rails for damage / wear.

Physically inspect bronze nut and screwbar for damage and wear by attempting to move the screwbar within the nut.

Visually inspect the bronze nut and screwbar for damage or wear. If excessive bronze shavings are presentunder the nut, remove and disassemble the nut for furthur inspection.

Left Side End Dam

Check oil in gearbox.

Inspect v-groove wheels and traverse rails for damage / wear.

Physically inspect bronze nut and screwbar for damage and wear by attempting to move the screwbar within the nut.

Visually inspect the bronze nut and screwbar for damage or wear. If excessive bronze shavings are present under the nut, remove and disassemble the nut for furthur inspection.

Applicator Exit Rollers

Remove any yarn from rollers and roller shafts.

Inspect roller headers for cracks, or any signs of wear / damage.

Inspect roller shafts for wear in /around the bearing.

Check all bearing set screws, tighten if necessary.

Grease all bearings, wipe excess grease off of grease fitting an bearing.

Pull Roller

Check oil in gearbox.

Inspect chains and sprockets for wear, alignment, and proper tension.

Remove any yarn from rollers and roller shafts.

Inspect roller headers for cracks, or any signs of wear / damage.

Inspect roller shafts for wear in /around the bearing.

Check all bearing set screws, tighten if necessary.

Grease all bearings, wipe excess grease off of grease fitting an bearing.

Inspect blue wrap on pull roller for wear.

Load Cell Roller

Remove any yarn from rollers and roller shafts.

*NOTE* Follow these steps for the roller above and below the load cell roller.

Inspect roller headers for cracks, or any signs of wear / damage.

Inspect roller shafts for wear in /around the bearing.

Check all bearing set screws, tighten if necessary.

Grease all bearings, wipe excess grease off of grease fitting an bearing.

Traverse

Remove guard from right side frame, above electrical panel.

Check oil in gearbox.

Inspect chains and sprockets for wear, alignment, and proper tension.

Inspect belts and pulleys for wear, alignment, and proper tension.

Inspect v-groove wheels and traverse rails for damage and wear.

Right Side End Dam

Check oil in gearbox.

Inspect v-groove wheels and traverse rails for damage / wear.

Physically inspect bronze nut and screwbar for damage and wear by attempting to move the screwbar within the nut.

Visually inspect the bronze nut and screwbar for damage or wear. If excessive bronze shavings are presentunder the nut, remove and disassemble the nut for furthur inspection.

Left Side End Dam

Check oil in gearbox.

Inspect v-groove wheels and traverse rails for damage / wear.

Physically inspect bronze nut and screwbar for damage and wear by attempting to move the screwbar within the nut.

Visually inspect the bronze nut and screwbar for damage or wear. If excessive bronze shavings are present under the nut, remove and disassemble the nut for furthur inspection.

Applicator Exit Rollers

Remove any yarn from rollers and roller shafts.

Inspect roller headers for cracks, or any signs of wear / damage.

Inspect roller shafts for wear in /around the bearing.

Check all bearing set screws, tighten if necessary.

Grease all bearings, wipe excess grease off of grease fitting an bearing.

NOTE Follow these steps for the roller above and below the load cell roller.