Sureshot Refrigerated Liquid Dispenser Monthly Cleaning

Remove & Clean Dispensing Valve Assembly – Portion Control Dispensers

• Prepare a container of warm, soapy water before you take the valve apart for cleaning. Be careful not to dislodge the cable during cleaning

• Turn the power to the dispenser OFF

• Open the dispenser door to the refrigerated product compartment

• Remove the product tanks

• Remove the catch tray (if applicable) by lifting it up and off

• Remove the 4 pan­head screws (+) that secure the front splash panel (valve cover) in place and carefully remove the panel

• Thoroughly wash the splash panel

• Open the valve door: unscrew the black knob in a counter­-clockwise motion

• Remove the Phillips­head screw at the top of the metal valve insert. Do not misplace the screw. Wipe clean

• Remove the 2 Phillips­head screws at the upper corners of the valve block. Do not misplace the screws. Wipe clean.

• Gently remove the white valve body, using an even force. Hold the valve carefully with one hand so that the thermistor wire will not be broken or damaged. Do not let the valve dangle freely. Hold it in your hands. The valve body can only be moved the length of the thermistor wire, which is located in the left valve

• Remove the plunger and spring. Wash, rinse, sanitize, and air dry the plunger and the spring

• Wipe the spring cup clean

• Clean the white plastic sections of the valve block, using a small brush with warm, soapy water. Rinse, sanitize, and air dry the white plastic sections of the valve block with the plunger and spring

• Air dry thoroughly

• Reassemble the spring, the plunger, and the valve body

• Align the valve body with the plunger then move back into place

• Replace the 2 Phillips- head screws. Tighten until snug. Do not over­-tighten the screws.

• Replace Phillips-­head screw at the top of the metal valve insert. This screw must fit snugly to ensure proper operation of the refrigeration system. Do not over­-tighten the screw

• Close the valve door

• Secure the door by tightening the knob-­screw in a clockwise motion until the door is snug. Do not over­-tighten the screw

• Re-­install 4 Phillips-head screws to secure the front panel in place

• Wipe the product compartment clean

• Close the refrigerated product compartment door

• Turn dispenser ON

• Push any “product” button, followed by any “size” button. Listen for the valve door open and close to ensure that the valve is operating properly

• Load new product and dispense

Remove & Clean the Dispensing Valve Assembly – Self­-Serve Dispensers

• Turn the power to the dispenser OFF

• Drain product tanks and remove empty tanks

• Open the door to the refrigerated product compartment

• Remove the catch tray (if applicable) by lifting it up and off

• Remove the 4 pan­-head screws (+) that secure the front splash panel/valve cover in place and carefully remove the front splash panel/valve cover. It is located below the white plastic valves that hold the product tubes. It is held in place by 4 Phillips­-head screws (+).

• Thoroughly wash the splash panel

• Open the valve door: unscrew the black knob in a counter-­clockwise motion

• Remove the Phillips-­head screw which retains the aluminum insert. Do not misplace the screw. Wipe the insert and screw clean

• Remove the 2 Phillips-­head screws at the upper corners of the valve block. Do not misplace the screws

• Remove the white valve body. Hold the valve carefully with one hand so that the thermistor wire will not be broken or damaged. The steel handle comes off with the valve body

• Remove the plunger tip and spring. Wash, rinse, sanitize, and air dry the plunger tip and spring.

• Wipe the spring cup clean

• Wash the handle, plunger tip and spring in warm, soapy water. Rinse with clear water. Dry thoroughly

• Clean the white plastic sections of the valve block, using a small brush with warm, soapy water. Dry thoroughly

• Clean the valve door front, valve door back, and insert

• Put the spring and plunger back together so that you can reassemble the valve body

• Align the valve body with the plunger. Move back into place

• Replace the 2 Phillips­-head screws. Tighten until snug

• Replace the Phillips­-head screw at the top of the metal valve insert. This screw must fit snugly to ensure proper operation of the refrigeration system. Do not over­-tighten the screw

• Close the valve door

• Secure the door by tightening the knob-­screw in a clockwise motion until the door is snug. Do not over­-tighten the screw

• Re-Close the refrigerated product compartment door­install the 4 Phillips-­head screws to secure the front panel in place

• Wipe the product compartment clean

• Close the refrigerated product compartment door

• Load new product and dispense

Product Case Cleaning

• Remove the product case from the refrigerated product compartment of the dispenser

• Wash with hot, soapy water or an approved sanitary cleaning product, according to provincial or state regulations

• Rinse with hot, clear water to remove soap residue

• Dry thoroughly