Back

18. WeatherMaker® Single Packaged Rooftop Units 48A: Monthly Maintenance and Cleaning

This procedure is for the monthly maintenance and cleaning of your unit. This is routine cleaning of coil surfaces is essential to maintain proper operation of the unit.
MaintainX
05/03/2021

18. WeatherMaker® Single Packaged Rooftop Units 48A: Monthly Maintenance and Cleaning

5 steps
This procedure is for the monthly maintenance and cleaning of your unit. This is routine cleaning of coil surfaces is essential to maintain proper operation of the unit.
  • ROUND TUBE PLATE FIN COIL MAINTENANCE AND CLEANING RECOMMENDATIONS

  • Routine cleaning of coil surfaces is essential to maintain proper operation of the unit. Elimination of contamination and removal of harmful residues will greatly increase the life of the coil and extend the life of the unit.

  • The following maintenance and cleaning procedures are recommended as part of the routine maintenance activities to extend the life of the coil.

  • Remove Surface Loaded Fibers

  • NOTE: Use of a water stream, such as a garden hose, against a surface loaded coil will drive the fibers and dirt into the coil. This will make cleaning efforts more difficult. Surface loaded fibers must be completely removed prior to using low velocity clean water rinse.

  • Periodic Clean Water Rinse

  • A periodic clean water rinse is very beneficial for coils that are applied in coastal or industrial environments. However, it is very important that the water rinse is made with very low velocity water stream to avoid damaging the fin edges. Monthly cleaning as described below is recommended.

  • Routine Cleaning of Coil Surfaces

  • Monthly cleaning with Totaline® environmentally balanced coil cleaner is essential to extend the life of coils. This cleaner is available from Carrier Replacement parts division as part number P902-0301 for a one gallon container, and part number P902-0305 for a 5 gallon container. It is recommended that all coils, including copper tube aluminum fin, pre-coated fin, copper fin, or E-coated coils be cleaned with the Totaline environmentally balanced coil cleaner as described below.

  • Coil cleaning should be part of the unit’s regularly scheduled maintenance procedures to ensure long life of the coil. Failure to clean the coils may result in reduced durability in the environment.

  • Avoid the use of:

  • Totaline environmentally balanced coil cleaner is non-flammable, hypoallergenic, nonbacterial, and a USDA accepted biodegradable agent that will not harm the coil or surrounding components such as electrical wiring, painted metal surfaces, or insulation. Use of non-recommended coil cleaners is strongly discouraged since coil and unit durability could be affected.

  • Totaline Environmentally Balanced Coil Cleaner Application Equipment:

  • ! CAUTION

  • Harsh chemicals, household bleach or acid or basic cleaners should not be used to clean outdoor or indoor coils of any kind. These cleaners can be very difficult to rinse out of the coil and can accelerate corrosion at the fin/tube interface where dissimilar materials are in contact. If there is dirt below the surface of the coil, use the Totaline environmentally balanced coil cleaner as described above.

  • ! CAUTION

  • High velocity water from a pressure washer, garden hose, or compressed air should never be used to clean a coil. The force of the water or air jet will bend the fin edges and increase airside pressure drop. Reduced unit performance or nuisance unit shutdown may occur.

  • Totaline Environmentally Balanced Coil Cleaner Application Instructions:

  • MICROCHANNEL HEAT EXCHANGER (MCHX) CONDENSER COIL MAINTENANCE AND CLEANING RECOMMENDATIONS

  • ! CAUTION

  • Do not apply any chemical cleaners to MCHX condenser coils. These cleaners can accelerate corrosion and damage the coil.

  • Routine cleaning of coil surfaces is essential to maintain proper operation of the unit. Elimination of contamination and removal of harmful residues will greatly increase the life of the coil and extend the life of the unit.

  • The following steps should be taken to clean MCHX condenser coils:

  • ! CAUTION

  • Excessive water pressure will fracture the braze between air centers and refrigerant tubes.

Please note that any procedure, checklist, or other document available in the MaintainX Global Procedure Library is provided for general education and information only and does not constitute legal, medical, or financial advice. MaintainX makes the materials available AS IS and AS PROVIDED, without warranties of any kind. By downloading or using any such materials, you assume the risk that they may not be appropriate for your specific situation and agree that you are solely responsible for any such use, including compliance with applicable law and with meeting any conditions of product warranties.