Back

WeatherMaker® Single-Packaged Rooftop Units with EcoBlue™ Technology 48FC: Condenser Coil Maintenance and Cleaning Recommendation

This procedure is for the maintenance of your condenser coil and cleaning recommendations of your equipment. The simple routine maintenance as described in this procedure will enhance your air conditioning system’s ability to operate economically and dependably.
MaintainX
05/03/2021

WeatherMaker® Single-Packaged Rooftop Units with EcoBlue™ Technology 48FC: Condenser Coil Maintenance and Cleaning Recommendation

7 steps
This procedure is for the maintenance of your condenser coil and cleaning recommendations of your equipment. The simple routine maintenance as described in this procedure will enhance your air conditioning system’s ability to operate economically and dependably.
  • Condenser Coil Maintenance and Cleaning Recommendation

  • Routine cleaning of coil surfaces is essential to maintain proper operation of the unit. Elimination of contamination and removal of harmful residues will greatly increase the life of the coil and extend the life of the unit. The following maintenance and cleaning procedures are recommended as part of the routine maintenance activities to extend the life of the coil.

  • REMOVE SURFACE LOADED FIBERS

  • Surface loaded fibers or dirt should be removed with a vacuum cleaner. If a vacuum cleaner is not available, a soft non-metallic bristle brush may be used. In either case, the tool should be applied in the direction of the fins. Coil surfaces can be easily damaged (fin edges can be easily bent over and damage to the coating of a protected coil) if the tool is applied across the fins.

  • NOTE: Use of a water stream, such as a garden hose, against a surface loaded coil will drive the fibers and dirt into the coil. This will make cleaning efforts more difficult. Surface loaded fibers must be completely removed prior to using low velocity clean water rinse.

  • Air Conditioning

  • Heating

  • Economizer or Outside Air Damper

  • Air Filters and Screens

  • Each unit is equipped with return air filters. If the unit has an economizer, it will also have an outside air screen. If a manual outside air damper is added, an inlet air screen will also be present.

  • Each of these filters and screens will need to be periodically replaced or cleaned.

  • Filters

  • RETURN AIR FILTERS

  • ! CAUTION

  • EQUIPMENT DAMAGE HAZARD

  • Failure to follow this CAUTION can result in premature wear and damage to equipment.

  • DO NOT OPERATE THE UNIT WITHOUT THE RETURN AIR FILTERS IN PLACE.

  • Dirt and debris can collect on heat exchangers and coils possibly resulting in a small fire. Dirt buildup on components can cause excessive current used resulting in motor failure.

  • Return air filters are disposable fiberglass media type. Access to the filters is through the small lift-out panel located on the rear side of the unit, above the evaporator/return air access panel. (See Fig. 3.)

  • FIG. 3

  • To remove the filters:

  • To re-install the access panel:

  • OUTSIDE AIR HOOD

  • Outside air hood inlet screens are permanent aluminum-mesh type filters. Check these for cleanliness. Remove the screens when cleaning is required. Clean by washing with hot lowpressure water and soft detergent and replace all screens before restarting the unit. Observe the flow direction arrows on the side of each filter frame.

  • ECONOMIZER INLET AIR SCREEN

  • This air screen is retained by filter clips under the top edge of the hood. (See Fig. 3.) FIG. 3

  • MANUAL OUTSIDE AIR HOOD SCREEN

  • SUPPLY FAN (BLOWER) SECTION

  • ! WARNING

  • ELECTRICAL SHOCK HAZARD

  • Failure to follow this warning could result in personal injury or death.

  • Before performing service or maintenance operations on unit, LOCKOUT/TAG-OUT the main power switch to unit. Electrical shock and rotating equipment could cause severe injury.

  • Supply Fan (Direct-Drive)

  • All FC units have the EcoBlue™ direct drive vane axial fan system. The fan is driven by an ECM motor with speed that is user set through the Unit Control Board (UCB). Speeds are fully configurable from 40% to 100% of motor’s maximum speed. See Fig. 5 and 6.

  • FIG. 6

Please note that any procedure, checklist, or other document available in the MaintainX Global Procedure Library is provided for general education and information only and does not constitute legal, medical, or financial advice. MaintainX makes the materials available AS IS and AS PROVIDED, without warranties of any kind. By downloading or using any such materials, you assume the risk that they may not be appropriate for your specific situation and agree that you are solely responsible for any such use, including compliance with applicable law and with meeting any conditions of product warranties.