Chick-fil-A Henny Penny PFE 500/PFG 600 Pressure Fryer Regular Maintenance Form Chick-fil-A Henny Penny PFE 500/PFG 600 Pressure Fryer Regular Maintenance Form
Filter pump motor protector-manual reset
Filtering of shortening Turn the thermostat and the main power switch to the OFF position Remove and clean the fry basket in soap and water Rinse thoroughly Use a metal spatula to scrape any build-up from the sides of the frypot. Do not scrape heating element on electric units, or the curved portion of the gas frypot Open the drain valve very slowly, half a turn at first and then slowly to the full open position. This will prevent excessive splashing of the hot shortening as it drains into the filter drain pan As the shortening drains from the frypot, use fryer brushes to clean the side of the frypot and the heating elements. If the drain fills with breading, use the white brush to push the breading into the filter pan When all of the shortening has drained, scrape or brush the sides and the bottom of the frypot Close the drain valve Open the filter valve Lower lid and hold closed Move the main power switch to the PUMP position. Carefully open the lid to see if the shortening is returning properly. Fill frypot 1/3 full, then turn off pump. Wash down and scrub the sides of the frypot. Use “L” brush to clean the heating elements. After the sides and bottom are cleaned, open the drain valve. Pump all the shortening out of the filter pan and back into the frypot. Close lid during first surge of pumping. When the pump is pumping air only, the shortening in the frypot will appear to be boiling. Close the filter valve first and then move the main power switch from PUMP to OFF. This will keep the filter pump and lines from filling up with shortening. Check the level of the shortening if necessary, until it reaches the level indicator line on the rear wall of the frypot, or the top level indicator line on model 500s. After completing the filtering operation, empty and replace the condensation drain pan If frying is to be continued at this time, move the main power switch back to the ON position, and allow time for reheating of the shortening
Cleaning the Optional Crumb Pan
Filter Pump Problem Prevention
Changing the Filter Envelope
Changing the Charcoal Filter
Cleaning the Frypot Turn the main power switch to OFF, and unplug unit from the wall receptacle If hot shortening is present in the frypot, it must be drained by slowly opening the drain valve handle one half turn. Leave for a few minutes, then slowly open the valve to the full open position Close the drain valve and discard the shortening in the filter pan. Then install the filter drain pan under the fryer, leaving out the filter screen assembly Fill the frypot to the level indicator with hot water. Add 4 to 6 ounces of fryer cleaner (Henny Penny part number 12101) to the water and mix thoroughly. The fry basket can be placed inside frypot for cleaning Set the thermostat to 195ºF and turn main power switch to the POWER position Do not close lid with water and/or cleaner in frypot. water under pressure becomes super heated. When lid is opened, escaping water and steam will result in severe burns When the heat light goes out and solution temperature is at 195ºF, immediately move the main power switch to OFF Pour a cup of hot cleaning solution (taken from the frypot) into the condensation tower to keep it free and clean Let the cleaning solution stand for 15 to 20 minutes with the thermostat off Using the fryer brush (Henny Penny part number 12105), scrub the inside of the frypot, the lid liner, and around the countertop of the fryer After cleaning, turn off the main power switch. Open the drain valve and drain the cleaning solution from the frypot into the drain pan and discard Replace the empty drain pan, close the drain valve and refill the frypot with plain hot water to proper level Add approximately 8 ounces of distilled vinegar and bring the solution to 195º F. Using a clean brush, scrub the interior of the frypot and lid liner. this will neutralize the alkaline left by the cleaning compound Drain the vinegar rinse water and discard Rinse down the frypot, using clean hot water Thoroughly dry the drain pan, and the frypot interior Replace the clean filter assembly in the drain pan and install under fryer Refill the fryer with fresh shortening
Cleaning the Deadweight Assembly
Please note that any procedure, checklist, or other document available in the MaintainX Global Procedure Library is provided for general education and information only and does not constitute legal, medical, or financial advice. MaintainX makes the materials available AS IS and AS PROVIDED, without warranties of any kind. By downloading or using any such materials, you assume the risk that they may not be appropriate for your specific situation and agree that you are solely responsible for any such use, including compliance with applicable law and with meeting any conditions of product warranties.
